← Back to blog

Freezing Rain and Your Heat Pump: What to Do in Maine

October 27, 2026
Freezing Rain and Your Heat Pump: What to Do in Maine

A freezing rain forecast does not mean you should shut your heat pump off, cover it or chip at it with a hammer. In most cases the right move is to leave it running, keep air moving around the outdoor unit and watch for ice that builds up and stays. This guide covers what freezing rain does to a heat pump, what ice is normal, when emergency heat makes sense, and what to check once the storm passes.

Hitamaine
Prepare Your Heat Pump for Maine Winters
HITA installs and maintains cold-climate heat pumps in Maine, with custom sizing based on detailed heat-loss calculations.
Explore HITA’s heat pump services

TL;DR

  • A thin layer of frost or ice on the outdoor unit is normal. Ice thicker than about 1/4 inch that does not clear during defrost is not.
  • Do not cover the unit, and never chip, pry or hammer ice off it. Both can cause more damage than the storm.
  • Keep the unit clear of snow drifts, branches and roof runoff before the storm, and leave it powered.
  • Emergency heat is for a unit that is damaged or cannot work, not a routine storm setting. If the fan is stuck in ice, switch to it and call a technician.
  • After the storm, check the fan, the sound, the airflow and the room temperature. Call a pro if anything is off.

Table of Contents

Why freezing rain is different from ordinary cold

An air-source heat pump pulls heat out of outdoor air, even very cold air. To do that, the outdoor coil has to be colder than the air around it. When the coil sits below freezing, moisture in the air can freeze on it. That frost reduces heat transfer and, if it builds up, eventually blocks airflow. The U.S. Department of Energy's Building America research describes this directly, and it explains why heat pumps run periodic defrost cycles that melt the ice and keep efficiency up.

On a dry, cold day, that system works quietly in the background. Freezing rain adds a second source of ice. Supercooled rain lands on the cabinet, the top grille and the fan guard, and freezes on contact. The unit is now fighting frost from the inside (condensation on the coil) and glaze from the outside (rain on the cabinet and fan). Defrost cycles are designed for the first problem. They are less able to handle a solid shell of ice that forms from the outside in.

Freezing rain glazing an outdoor heat pump grille

In Maine, where the outdoor unit may already be under a load of snow, ice and wind, it helps to know which ice is routine and which needs action.

Normal ice versus a problem

Heat pump manufacturers describe a light layer of frost or ice, generally under 1/4 inch, as normal winter operation. You will see it come and go as the unit cycles in and out of defrost.

During a defrost cycle you may also notice:

  • Steam or vapor rising from the outdoor unit.
  • A brief "swoosh" sound as refrigerant reverses direction.
  • The indoor fan slowing or stopping for a few minutes.
  • Cooler air from the indoor unit for a short time.

The steam and swooshing are typical and harmless signs that the system is melting frost, because the unit briefly runs in cooling mode to warm the outdoor coil. Efficiency Maine's own guidance tells owners not to worry about snow and ice accumulating on the unit, since heat pumps defrost automatically, while clearing drifts and debris away from it.

We wrote a separate piece on what a normal defrost cycle looks like, and why lingering ice isn't normal. If your indoor unit also blows cool air for a few minutes during defrost, that is usually normal in cold climates too.

Signs the ice is a problem

The pattern to worry about is ice that stays. Look for:

  • A solid coating or ice thicker than about 1/4 inch that does not clear after a defrost cycle.
  • Ice bridging the fan blades or the gap between the blades and the guard.
  • Grinding, rattling or other unusual noises.
  • A breaker that trips repeatedly.
  • A home that will not reach the set temperature.

These match the conditions where a technician should be called. The stakes are real. The Department of Energy research notes that in extreme cases, inadequate defrosting can lead to ice buildup that damages internal components, including cracked copper refrigerant tubing.

Keep it running or switch to emergency heat?

This is the question behind most searches about a heat pump in freezing rain, and the advice you will find is not uniform.

The case for leaving it on normal heat. A modern cold-climate heat pump is built to run in sub-freezing weather. Normal heating mode keeps the defrost cycle working, which is the very thing that clears ice. If your system has a backup heat source, it will bring that in automatically when the heat pump cannot keep up.

The case for emergency heat. Some HVAC professionals advise switching to emergency heat during severe freezing rain, as a precaution so the outdoor fan does not make contact with ice and cause costly repairs. Others stress that emergency heat is not meant for routine cold-weather use, but for situations where the outdoor unit is damaged or cannot work.

Our view sits between the two, and it depends on what you see:

  1. Unit looks normal, defrosting, ice is thin. Leave it on regular heating mode.
  2. Fan blades are encased in ice or the fan is not turning. Switch to emergency heat to stop the outdoor unit running against ice, and call a technician. Do not try to free the fan by force.
  3. Unit is visibly damaged, making grinding noises, or shut down on a fault. Emergency heat and a service call.

Know that emergency heat typically means electric resistance backup, which costs far more to run than the heat pump. Use it for hours, not days, and only when the situation calls for it. If you have a dedicated backup such as an oil boiler or furnace, ask your installer how it is set up to take over. Your thermostat's lockout setting also controls when the heat pump hands off to backup heat; our guide to heat pump lockout temperature settings for Maine explains what to choose.

How to protect your heat pump before an ice storm

Most of the protection happens before the weather arrives, and most of it is about airflow and where water lands.

Do not cover the unit

It is tempting to wrap or tarp the outdoor unit. Don't. Federal guidance for owners of air-source heat pumps says to avoid covers because they restrict the airflow the unit needs to extract heat. A tarp also traps moisture against the cabinet and can freeze to it. If you are weighing a hard top shield instead, see our guide to heat pump covers for winter in Maine.

Control roof runoff

The same guidance points to where the unit sits. Placing it on the gable end of the house, under an eave, or beneath a snow shield for overhead protection keeps meltwater and falling ice off the top of the unit. If your installation sits directly under an unguttered roof edge, that is worth fixing before January, not during the storm.

Clear the space around it

Leave at least two feet of clearance on all sides and trim overhanging branches or clean gutters before winter weather arrives. Falling limbs are the other storm risk: a branch laden with ice can crush fins or bend a fan guard. Remove loose leaves from the unit, being careful not to bend the fins, as Efficiency Maine advises.

Raise it above the snowline

A unit sitting at ground level in a snowy yard will be buried by the first storm. A wall bracket or a stand that lifts it well above typical snow depth keeps the coil and the drain area open. This is something we plan for during installation, and it is one reason heat-loss sizing and placement are decided together. Our installation planning page describes how that works.

Check the drain path

Melted frost has to leave the unit. If the base pan or drain holes are packed with ice, water refreezes inside the cabinet and the ice builds from the bottom up. Look at the base before winter, keep leaves and debris out of it, and make sure nothing blocks the underside.

If ice builds up during the storm

Stay calm and stay out of the unit with tools.

Do:

  • Watch the unit from a window or the doorway at intervals, if it is safe to do so. Do not go outside under ice-laden branches or onto a glazed walkway.
  • Confirm the unit is still defrosting. You should see steam and the fan stop and start.
  • Switch to emergency heat if the fan is blocked by ice, as described above.
  • Note what you see: how thick the ice is, which parts it covers, what sounds you hear. A technician will ask.

Do not:

  • Chip, pry or hammer the ice. Tools can damage the coils and fan blades, and a punctured coil means a refrigerant leak and a costly repair.
  • Pour hot water over the unit. It refreezes, and the thermal shock is not good for the cabinet.
  • Cut power to the unit mid-storm without a reason. It stops the defrost cycle from working.
  • Use a heat gun, torch or open flame near the unit.

If ice has formed on the indoor coil rather than the outdoor unit, the causes are different. Our guide to safe DIY checks to thaw a frozen evaporator coil walks through them.

After the storm: how to check your heat pump is working properly

Once the ice melts and it is safe to be outside, spend ten minutes on the unit. This is a practical walk-around, not a diagnostic.

  1. Look at the fan and guard. The fan guard should be straight, with no cracks. Blades should be clear of ice and debris. With the power off at the disconnect, you should be able to see them without anything touching.
  2. Check the cabinet and fins. Look for dents, crushed fins or limb damage. Do not comb or poke the fins.
  3. Check the base and drain area. Ice or leaves should not be packed under or around the unit. Keep the clearance around it open.
  4. Restore normal settings. If you switched to emergency heat, return the thermostat to regular heating mode once the unit is clear.
  5. Listen on the first cycle. A steady hum is normal. Grinding, scraping, banging or a loud rattle is not.
  6. Feel the airflow indoors. After a minute or two, the indoor unit should deliver warm air at a steady speed. Remember that a short pause for defrost is normal.
  7. Watch the room temperature. Over the next few hours, the house should climb toward your setpoint. If it does not, the system may be struggling. Our no-heat checklist for Maine heat pump owners covers the quick checks before you call.
  8. Check the breaker and the thermostat. A breaker that trips again after you reset it once means stop and call.

If the unit passes all eight, it is almost certainly fine. If it fails any one of them, do not keep running it and hope.

Our perspective: ice is a design and maintenance issue

We install and service cold-climate heat pumps across Maine, and storm calls tell us the same story. Units that handle freezing rain well are rarely lucky. They are placed out of roof runoff, mounted above the snowline, sized from a real heat-loss calculation so they are not running flat out for days, and kept clean enough that defrost works as designed.

Our perspective: ice is a design and maintenance issue — overview diagram

An oversized or undersized system, a clogged coil, or a blocked drain makes ice worse. A coil packed with dirt does not shed frost evenly, and a unit that cannot keep the house warm runs constantly in the worst conditions. That is why we start with heat-loss numbers rather than rules of thumb, and why we recommend a pre-winter inspection rather than a storm-night scramble. If you want to know more about the pre-winter visit, read our piece on whether cold homes need two maintenance visits a year.

Our practical advice is simple: do not cover it, do not hit it, keep it clear, and call us when the ice does not leave. We would rather take a call about ice that turned out to be normal than one about a cracked coil.

— John

Get the unit ready before the next storm

A clean coil and a clear drain are the cheapest protection a heat pump has. Our one-time deep cleaning starts from $249, and our annual plans bundle the care into a yearly visit: the Annual Cleaning Plan is $219 per year, and the Maine Heat Pump Care Plan is $319 per year. You can compare them on our plans page. We confirm service by ZIP code before scheduling or payment, so we only book where we can actually serve you.

If you want to understand what cleaning involves first, see how homeowner filter and drain care differs from coil cleaning that needs a pro.

When to call a technician

Call a heating professional if you see any of these once the storm is over, or during it if your home is losing heat:

  • Ice thicker than 1/4 inch, or a solid coating, that stays through several defrost cycles.
  • Fan blades that will not turn or that strike something.
  • Unusual noises, from grinding to loud banging.
  • A breaker that trips repeatedly.
  • A house that does not reach the set temperature on normal heat.
  • Visible damage: crushed fins, a bent cabinet, oil or fluid on the base.

Tell the technician what mode the unit was in, how long the ice has been there and whether you used emergency heat. If you are in our service area, you can reach us through our main site and we will confirm coverage by ZIP code.

FAQ

Can a heat pump freeze up in freezing rain?

Yes. Water from rain, melting snow or condensation can freeze on the coil and fan area when temperatures are below freezing. A thin layer under about 1/4 inch is normal and clears during defrost. Ice that is thicker, or that stays after defrost, means you should call a technician.

Should I turn on emergency heat during an ice storm?

Not as a default. Leave the system on regular heating if the unit is defrosting and the ice is thin. Switch to emergency heat if the fan is stuck in ice or the unit is damaged, and call for service. Emergency heat is usually electric resistance and costs more to run, so use it briefly.

Is it okay to cover my heat pump during an ice storm?

No. Covers restrict the airflow the unit needs, and a tarp can trap moisture and freeze to the cabinet. Protect the unit by clearing the space around it, managing roof runoff, and using a rigid overhead shield if your installation needs one.

How do I get rid of ice on my heat pump?

First let the defrost cycle do its work. Do not chip, pry or hammer the ice, because tools can damage the coils and fan blades. If thick ice remains after several cycles, call a technician rather than forcing it.

Will snow and ice damage a cold-climate heat pump in Maine?

Snow and thin ice on the unit are normal, and Efficiency Maine says not to worry about them. The real risks are ice that blocks the fan, falling branches and runoff from the roof. Good placement and regular maintenance reduce all three.

Sources