A heat pump and a wood stove work well together. The heat pump carries the everyday heating load, and the stove adds heat on the coldest days or when you want it. That is how many Maine households already heat: in Efficiency Maine's metered study, 31% of homes used wood as supplemental heat. The pairing works best when the heat pump is sized from a real heat-loss calculation, so it can do most of the job without leaning on the stove. That is how we design every system at Hita.
TL;DR
- Let the heat pump be your base heat and use the wood stove to take over peak demand on the coldest days, as Efficiency Nova Scotia describes.
- Wood is common in Maine: 31% of metered heat pump homes used it as a supplement, and 58% of Hancock County households burn at least some.
- Do not switch the heat pump off at 20°F out of habit. Sizing and settings matter more than a cutoff temperature.
- A stove in one room heats that room best. A heat pump with the right zones spreads comfort through the rest of the house.
- Both need yearly attention: a chimney inspection for the stove and a technician visit plus clean filters for the heat pump.
Table of Contents
- Why the two heat sources fit together
- What each one does best
- How to split the work: when each one should run
- What it costs to run both
- Spreading the heat through the house
- Will a wood stove heat the whole house?
- Safety and maintenance for both
- Perspective: why we start with the heat pump
- Getting the setup right
- How Hita can help
- FAQ
- Sources
Why the two heat sources fit together
The two appliances solve different problems. A heat pump moves heat from outdoor air into your home using electricity. A wood stove makes heat by burning fuel in one spot. One is steady and automatic. The other is strong and local.
Efficiency Nova Scotia's guide on using a heat pump with a wood stove frames it simply: the heat pump covers the base heat demand, and the wood stove takes over at peak demand on cold days. When the stove warms the house, the heat pump has less to do, so it runs less and its electric resistance elements switch on less often. If you are not sure what those elements are, see our guide to how cold-climate heat pumps work in Maine winters.
Maine homeowners did not invent this habit for heat pumps. Wood was in the house first. A UMaine study of Hancock County found that 58% of households use at least some wood for heat, and about half of those get half their heat from wood. Adding a heat pump to a house that already has a stove is a very ordinary Maine upgrade.
What each one does best
| Job | Heat pump | Wood stove |
|---|---|---|
| Steady heat all day and night | Runs automatically on a thermostat | Needs tending and reloading |
| Heating several rooms | Ductless, multi-zone or ducted systems reach many rooms | Heats the room it sits in best |
| Cooling in summer | Yes, the same equipment cools | No |
| Power outage | Needs electricity | Keeps working without it |
| Cold snap boost | Works within its rated capacity | Adds a lot of heat quickly |
| Cozy radiant warmth | Gentle, even air heat | Strong radiant warmth |
The table shows why the combination makes sense rather than why one should replace the other. You get automatic comfort from the heat pump and a strong, independent heat source in the living room.
How to split the work: when each one should run
The practical question is who is in charge. We recommend a simple rule: the heat pump is the default, and the stove is a deliberate addition.
Let the heat pump run as the base
A properly sized cold-climate heat pump can keep running well into the cold. The measured data backs this up. In Efficiency Maine's evaluation of metered Maine homes, the heat pumps averaged a seasonal COP of 2.57, which means roughly 2.57 units of heat delivered for each unit of electricity used. The study also reported that these homes used an average of 1,887 kWh per year for heating.
That is why the stove does not need to run all day to keep bills down. The heat pump is already efficient across the season.
Bring in the stove on peak days and in the evening
The stove earns its place in three situations:
- The coldest stretch of winter. Heat pump output falls as the temperature drops. Our article on planning for 48–68% heat pump capacity at 5°F explains what to expect, and a stove covers the gap.
- Evenings at home. If the family gathers in one room, a fire there takes the chill off while the heat pump keeps the rest of the house comfortable.
- A power outage. The stove keeps one part of the house warm when the grid is down.
When the stove is burning, you can turn the thermostat for that zone down a degree or two so the heat pump is not working against the fire.
Do not shut the heat pump off at 20°F
Here is a common mistake in Maine. In the Efficiency Maine study, some homeowners switched their heat pumps off at around 20°F because they believed the pump's falling capacity would make it cost more than oil below that point. Others used it only intermittently: 19% turned it on and off as needed, and several turned it on in the morning to take the chill off and off at night.
That pattern leaves the heat pump doing less and your backup doing more. If you have wood, it can quietly become your main heat even when you did not plan it that way. If you want the heat pump to carry the base load, leave it on through the cold with a steady setpoint and let the stove top up the heat.
What it costs to run both
Maine publishes weekly heating fuel prices, and they make a fair comparison possible. In the state's April 6, 2026 price sheet, electricity for air-source heat pump heating was $0.1044–$0.1102 per kWh, cordwood was $355 per cord, pellets were $357 per ton, heating oil was $5.43 per gallon and propane was $3.39 per gallon. The January 12, 2026 sheet showed the same electricity, cordwood and pellet prices with oil at $3.46 per gallon. Check the current sheet before you budget, because oil and propane move week to week.
A worked example for the heat pump side
One million Btu (1 MMBtu) is about 293 kWh of heat. At the study's average COP of 2.57, the heat pump uses about 114 kWh of electricity to deliver that. At $0.1044 to $0.1102 per kWh, that is roughly $11.90 to $12.60 per MMBtu delivered. This is our own arithmetic from those two published figures, so your result will shift with your rate and your system's actual performance.

For wood, your cost depends on the price per cord you pay, how dry the wood is and your stove's efficiency, so work out your own figure from your last delivery. If you cut your own wood, your cost is mostly time.
Efficiency Maine also reported that its rebated heat pumps produced large annual energy savings and displaced pellet and cordwood heat as well as fossil fuels. The study put the displacement at 46,000 MMBtu of pellet and cordwood heat. A heat pump reduces how much wood you need to burn, so you can burn wood by choice rather than by need.
Why a heat pump bill can look high
If your bill is higher than you expected, look at how the system is being used before you blame the equipment. The evaluation points to operating habits: shutting off in the cold, intermittent running and how much load still lands on the heat pump. A home with leaky windows, a drafty attic or a heat pump that is too small for the space will use more electricity. A heat pump with dirty filters or a clogged coil works harder as well. Our guide to heat pump electricity usage in Maine walks through what to expect.
Spreading the heat through the house
The classic complaint about a wood stove is that the living room is toasty and the bedrooms are cold. A heat pump helps because it is designed to serve more than one space.
- Ductless mini-splits put a wall unit in a room or open area. A single-zone unit near the stove room can keep the adjacent space comfortable.
- Multi-zone systems connect several indoor units to one outdoor unit, so bedrooms and the main living area can each have their own setting.
- Ducted systems deliver air through existing or new ductwork for an even feel across the house.
We offer all three, and the right choice comes from your floor plan and your heat-loss numbers. With a stove in the house, the usual goal is to place the heat pump so it does not fight the stove. An indoor unit mounted directly across from the stove can read the stove's heat as the room temperature, and then shut down when the other rooms still need heat. Locate it where it reads the room accurately, or use a zone setup that keeps the other rooms covered.
For control settings, aim for these habits:
- Choose a steady setpoint for the heat pump in each zone, rather than turning it on and off.
- When you light the stove, lower the setpoint in that zone by a degree or two.
- In the coldest weather, leave the heat pump running and add wood for comfort.
- Use the fan on the stove or the indoor unit's fan setting to move warm air toward the cooler rooms.
If you are comparing this arrangement with a backup furnace or boiler, our article on dual fuel heat pumps and where they fit in Maine covers that route.
How a heat pump performs in the cold also depends on the unit itself. For background on air source heat pump basics, including capacity and efficiency as temperatures drop, this overview is a good place to start.
Will a wood stove heat the whole house?
It depends on the house, but it is not the best plan. A stove puts a lot of heat into one room. How much of that reaches the rest of the home depends on the layout, doors and how well the house holds heat. Efficiency Nova Scotia treats the stove as an add-on for peak-load relief, with the heat pump providing base heat for the house. That is the sensible way to design it: the heat pump provides even coverage and the stove adds comfort and resilience.
The reason is partly practical. Keeping a fire going all night means feeding it, and the heat falls off when the fire dies down. A thermostat-driven heat pump does not.
Safety and maintenance for both
Wood heat and electric heat have different upkeep. Keep both on a schedule.
The stove and chimney
Follow the manufacturer's installation instructions and keep the required clearances to anything combustible. Forward Mutual's loss-control guidance says to inspect stove pipes and the chimney each year before use, looking for cracked flue liners, broken or missing bricks, creosote deposits, bird nests and other foreign material. It also says to check for creosote frequently and recommends professional chimney cleaning. Have your chimney inspected and cleaned by a qualified chimney professional, and make sure you have working smoke and carbon monoxide alarms near the stove and sleeping areas.

The heat pump
The Clean Energy States Alliance's Vermont guide recommends that a qualified technician inspect heat pump equipment at least annually, that air filters be checked monthly and cleaned or replaced as needed, and that the outdoor unit be checked for dust, pollen, ice and snow and kept clear. The same guide notes that advanced wood heating equipment also needs annual servicing.
In a house with a stove, the heat pump's indoor unit can collect dust and fine ash from the room, so a regular filter routine is worth keeping. The outdoor unit needs clear space around it in winter. If you are thinking about covers, read what to use first in our guide to heat pump covers for winter in Maine. If the unit is not heating, our 5 checks for Maine heat pump owners come before a service call.
Perspective: why we start with the heat pump
We install heat pumps in Maine homes that already burn wood, and the best results come from deciding the roles before the equipment is chosen. The heat pump is the base. The stove is the extra.
That only works if the heat pump is designed for Maine. We size systems from detailed heat-loss calculations and select cold-climate equipment built to keep working when temperatures fall to −22°F or lower. A system sized that way can carry the house through most of winter, so your wood becomes a choice and a backup rather than a chore you cannot skip.
We also look at the whole house. The stove room, the bedrooms and the open areas each need their own answer, and ductless, multi-zone and ducted systems all have a place. We guide you through rebate eligibility as part of planning, so you know what to expect before you commit.
Then comes upkeep. A system that is cleaned and checked every year performs better and lasts longer, which is why we built annual care plans around it.
John
Getting the setup right
If you are adding a heat pump to a home with a stove, a few steps get you there with fewer surprises. Our step-by-step guide to the installation process in Maine covers the full sequence, and these are the points that matter for a stove house:
- Start with a heat-loss calculation. It tells you how much heat the house needs on a design-cold day, which sets the heat pump size and how much the stove has to cover.
- Pick the system type for your layout. Ductless, multi-zone or ducted, based on how heat moves through your rooms.
- Place indoor units away from the stove's direct heat. This keeps the thermostat reading honest.
- Plan the controls. Decide the setpoints for each zone and when the stove is allowed to take over.
- Set up yearly care. One visit for the heat pump, one for the chimney, both on the calendar.
If your current heat pump is the issue, whether it is undersized, aging or struggling in the cold, a change-out with proper sizing can fix the root problem. Our guide to how long heat pumps last in Maine can help you judge where yours stands.
How Hita can help
We install and replace cold-climate heat pumps across Maine, with sizing based on heat-loss calculations and guidance on rebate eligibility. Service is confirmed by ZIP code before any appointment or payment. You can see what we do on our services page and read how we plan a job on our installation planning page.
For ongoing care, we offer two annual plans on our plans page: the Annual Cleaning Plan at $219 per year and the Maine Heat Pump Care Plan at $319 per year. A one-time deep cleaning starts at $249. The plan terms are on our care plan terms page.

To talk through a heat pump that works alongside your stove, start at hitamaine.com.
FAQ
Can I use a heat pump and a wood stove at the same time?
Yes. Efficiency Nova Scotia describes the heat pump as covering base demand while the stove takes over at peak demand. When the stove is lit, lower the setpoint in that zone slightly so the heat pump does not work against it.
Will a wood-burning stove heat a whole house?
A stove heats its own room best, and how far the heat travels depends on your layout. Most households use it as a supplement. A properly sized heat pump with the right zones provides even heat across the rest of the house.
Why is my bill so high with a heat pump?
Often it comes down to use and load. Efficiency Maine found that some owners shut their heat pumps off around 20°F or ran them only intermittently. Drafty rooms, dirty filters and an undersized system also raise electricity use, so check settings, filters and sizing together.
Is a pellet stove cheaper than a heat pump?
In Maine's April 6, 2026 price sheet, pellets were $357 per ton and heat pump electricity was $0.1044–$0.1102 per kWh. Your cost per unit of heat depends on your stove's efficiency and the heat pump's performance, which averaged a COP of 2.57 in Efficiency Maine's metered homes.
How often should I service each one?
Have a qualified technician inspect the heat pump at least once a year and check the filters monthly. Have the stove pipe and chimney inspected every year before the burning season and cleaned as needed.
Sources
- How to Use a Heat Pump With a Wood Stove, Efficiency Nova Scotia
- 2024 Residential Heat Pump Impact Evaluation Report, Efficiency Maine
- Modern Consumer Families and Self-reliant Maine Yankees, University of Maine
- Maine Heating Season Weekly Prices, April 6, 2026
- Maine Heating Season Weekly Prices, January 12, 2026
- Safety Guidelines for Solid-Fuel Burning Appliances, Forward Mutual
- A Vermonter's Guide to Residential Clean Heating and Cooling, CESA
